Время намазов

Ats20 | Firmware Exclusive

Unlocking the Full Potential of Your ATS-20: The "ATS_EX" Firmware Guide If you’ve picked up an

DSP receiver, you already know it’s one of the best "bang-for-your-buck" portable radios out there. But out of the box, the stock firmware can feel a bit basic. Enter the "exclusive" community-favorite upgrade: the ATS_EX Advanced Firmware by Goshante This firmware pushes the humble Arduino Nano

inside your receiver to its absolute physical limits, offering features that make it feel like a much more expensive piece of kit. Why Upgrade to ATS_EX? ATS_EX firmware

isn't just a minor patch; it’s a complete "re-imagining" of the user interface. Here is why enthusiasts from the Si47XX Radio Experimenters group are making the switch: Optimized Performance

: This code is stripped down and optimized to fit the limited flash memory of the ATS-20, squeezing every drop of power out of the Si4732/35 DSP chip Enhanced Signal Metering

: Adds a visual signal level bar (S-meter) at the bottom of the screen via a long press of the SSB Sync Mode

: Improved handling for Single Side Band (SSB) modulation, including a dedicated sync mode accessible through the Better Band Navigation

: A refined "Band selection mode" allows for faster scrolling through subbands and quick switches between FM and SW. Audio Fixes

: Newer iterations (v2 and v3) have even worked on experimental fixes to eliminate the annoying "audio pops" during tuning. How to Install the Upgrade

Ready to flash? You’ll need a few tools and a bit of patience. ATS_EX Firmware for ATS-20 DSP Receiver - GitHub

ATS_EX firmware goshante on GitHub is the most widely discussed "exclusive" or advanced upgrade for the ATS-20+ radio. It is often described as a "game changer" that transforms the device from a basic shortwave toy into a viable tool for amateur radio operations. Key Features & Improvements Reduced "Chuffing":

Significant reduction of the "soft mute" effect, making scanning through bands much smoother. Fine-Tuning: Adds a precise 10 Hz tuning step

for SSB (Single Sideband), which is essential for clearly receiving ham radio operators. Visual Overhaul:

Introduces a cleaner, high-contrast display with larger fonts that are easier to read than the original factory version. Advanced Audio Tools: Includes a Synchronous Detector (SAM)

for AM modes to reduce fading distortion and the ability to adjust receive bandwidth via the encoder. Battery Management: ats20 firmware exclusive

For the ATS-20+, it supports built-in battery level indication using existing resistor dividers. Performance & User Experience

Users frequently highlight that this firmware pushes the hardware to its absolute limits; the developer has stated that the flash memory is nearly full, so further feature requests are generally closed. While many praise the S-meter implementation

as the best available for this device, some users have noted minor audio distortion when the S-meter is active during SSB reception. Installation Notes

The "ATS20 firmware exclusive" likely refers to the ATS_EX firmware, an advanced, community-developed update for the ATS-20 and ATS-20+ DSP receivers. Developed by Goshante and based on the PU2CLR library, it is designed to unlock features that the factory firmware (typically V1.1.5) cannot provide due to hardware and software limitations. Key Exclusive Features of ATS_EX

The ATS_EX firmware focuses on a "cleaner" experience and more granular control for radio hobbyists:

Reworked Interface: Replaces stretched, cluttered fonts with a minimalistic 7-segment frequency display inspired by closed-source high-end versions.

Integrated BFO: Unlike the standard firmware where BFO (Beat Frequency Oscillator) is a separate menu setting, ATS_EX integrates it into the main frequency dial during SSB mode for seamless tuning.

Expanded Tuning Steps: Offers precise SSB steps (10/25/50/100/500Hz) and broad AM steps up to 1MHz.

Extended Band Ranges: Covers LW (153-520 KHz), MW (520-1710 KHz), SW (1700-30000 KHz as one continuous band), and FM (64-108 MHz).

Advanced Audio Controls: Includes a Mute button, display on/off toggle, and adjustable CPU Frequency to reduce internal interference and save power.

Dynamic RDS: FM mode features scrolling Radio Data System information (up to 16 characters). Community Alternatives

While ATS_EX is the most prominent, other "exclusive" modifications exist:

PU2CLR (v3.0.7g): Focuses on technical fixes, such as correcting encoder direction and adding an AVC (Automatic Volume Control) function.

Custom "SDR1024" Builds: Certain retail versions like the ATS-20+ 1024 come with exclusive hardware integrations, including a built-in ADC for battery voltage monitoring that requires specific firmware support. Installation & Risks Updating the ATS-20 is a manual process that involves: Lets upgrade the ATS 20+ Unlocking the Full Potential of Your ATS-20: The

The ATS-20 and its successor, the ATS-20+, have gained a cult following in the ham radio community, largely due to "exclusive" community-developed firmwares that transform these budget-friendly devices into surprisingly capable receivers. The "Exclusive" Edge: ATS_EX Firmware

While the stock radios typically ship with basic PU2CLR firmware (often version 1.15), the ATS_EX firmware by Goshante is widely considered the gold standard for "exclusive" upgrades. It is an advanced build specifically for the Arduino Nano/Uno and Si473x DSP chip architecture. Key Exclusive Features

Upgrading to a version like ATS_EX v1.18 offers several features not found in stock versions:

Refined SSB Tuning: BFO (Beat Frequency Oscillator) is integrated into the main frequency, allowing for seamless tuning without a dedicated menu option.

Fine-Grained Steps: Offers precise tuning steps as low as 10Hz for ham radio operations, whereas stock firmware often starts at 25Hz.

Enhanced Interface: Features a "7-Segment" frequency font and a minimalistic, more readable OLED layout that eliminates the "stretched" look of factory software.

Advanced Control Suite: Adds a settings page for AGC (Auto Gain Control), Soft Mute, and AVC (Automatic Volume Control) customization.

Hardware Modifications: The firmware supports a battery level indicator, though this requires a small physical modification (soldering a voltage divider to pin A2). How to Upgrade

Flashing these "exclusive" firmwares requires a computer and a few simple tools:

Identify Your Revision: Disassemble the unit to see if it uses an Arduino Nano (soldered as a separate board) or an Arduino Uno (components soldered directly to the main PCB).

Required Software: Most users use AVRDUDESS (for Windows) or the Arduino IDE to flash the .hex binary file.

Drivers: Ensure you have the CH340/CH341 USB serial driver installed to recognize the radio's port.

Critical Step: After flashing, it is strongly recommended to reset the EEPROM by holding the Encoder Button while powering on the device. Popular Sources for Custom Firmware

GitHub - goshante/ats20_ats_ex: The official repository for the ATS_EX advanced firmware. Better AGC (Automatic Gain Control): Smoother audio without

GitHub - patomoi/ATS-20-Starter-Pack: A collection of libraries and sketches for those who want to compile their own code. ATS_EX Firmware for ATS-20 DSP Receiver - GitHub

I’m unable to provide a full guide or copy of exclusive or proprietary ATS20 firmware (e.g., closed-source versions from vendors like ZL2CX, N7DDC, or custom-locked binaries).

However, I can give you a complete, actionable guide for working with open ATS20 firmware (mainly ATS-20 by SQ5RWU / IU3HXX) and explain how to identify/install exclusive versions if you already have the legal rights or files.

1. The "Spectrum Waterfall" on a $40 Device

The most coveted exclusive feature is the real-time FFT Spectrum Analyzer and Waterfall. In the stock firmware, you get a single S-meter. In custom builds (like the famous "Modified FW by SQ5RWU" or "RX-888" inspired ports), the tiny OLED screen is repurposed to show a live RF panorama.

Exclusive capability: You can see a 100kHz-wide snapshot of the band. As you spin the dial, a cursor moves across the spectrum. This is usually a feature reserved for SDRs connected to a PC. On the ATS20, it’s embedded into the standalone firmware, allowing you to visually hunt for pirate radio stations, distant amateur SSB calls, or even nearby switching power supply noise—all without a laptop.

2. Enhanced Demodulation & DSP

While the hardware (SI4735 chip) handles the signal, the firmware dictates how it is processed. Custom builds often tweak the Digital Signal Processing (DSP) parameters, resulting in:

Top 3 Exclusive Firmware Builds You Need to Try (2024-2025 Edition)

If you search for "ATS20 firmware exclusive," you will find many dead links. Here are the three active, high-quality builds currently available.

Conclusion: The Hacker's Radio

The ATS20 is not a radio. It is a hardware shell waiting for a soul. The exclusive firmware transforms a mediocre Chinese portable into a spectrum analyzer, a RTTY terminal, a stealth receiver, and an IF tap.

For the average user, the stock firmware is fine. But for the RF hacker, the digital minimalist, or the survivalist who wants a single device that can read airplane data, print text from radio waves, and visualize the invisible world around them—the exclusive ATS20 firmware is the only reason to buy this hardware.

Verdict: Don't buy an ATS20 for the hardware. Buy it for the potential. And that potential lives exclusively in the firmware you flash after dark.

The phrase "ATS20 firmware exclusive" likely refers to community-developed, third-party firmwares that offer features not available in the factory software (v1.1.5). These updates are essentially "exclusive pieces" of software that unlock the full potential of the SI4732/SI4735-based ATS-20 and ATS-20+ receivers. Key "Exclusive" Firmware Options

ATS_EX by Goshante (v1.18): Considered a major "exclusive" upgrade, it features a completely reimagined, minimalistic interface that replaces the stock "stretched" fonts with a 7-segment style frequency display. It also integrates BFO (Beat Frequency Oscillator) directly into the main tuning process and adds an S-meter.

PU2CLR Library-Based Firmware: Many exclusive community builds are based on the PU2CLR SI4735 Arduino Library. Newer versions (v3.0.4+) provide significantly more features than the original stock version pre-loaded on most devices.

ATS_mini_RTty_Morse_Code_Decoder: Specific versions of firmware for related SI4732 devices (like the ATS Mini) include specialized decoders for CW (Morse) and RTTY, which are not present in standard builds. Common Features Unlocked

Upgrading to these exclusive firmware "pieces" typically provides: