The Daikin BRC4C160 is a wireless remote controller kit commonly used with VRV and SkyAir indoor units. This guide outlines essential operating procedures and diagnostic steps based on official Daikin Manuals. Core Operations
ON/OFF: Press the START/STOP button to begin or end operation. A red indicator lamp on the receiver stays lit during operation. Mode Selection: Use the MODE button to cycle through: Cool: For temperature reduction (Set range: 18∘C18 raised to the composed with power C 32∘C32 raised to the composed with power C Heat: For warming the room (If supported by unit). Dry: To reduce humidity without significant cooling. Fan: For air circulation only.
Fan Speed: Toggle between High or Low settings using the fan speed control button.
Timer: Press the TIMER button and use UP/DOWN to set start or stop times. Service & Troubleshooting Wireless Remote Controller Kit - Daikin Europe
The Daikin BRC4C160 Go to product viewer dialog for this item.
is a wireless remote controller kit primarily used for Daikin VRV and commercial air conditioning systems. It provides comprehensive control over indoor unit operations, including temperature adjustment, mode selection, and fan speed. Core Controls and Functions
The BRC4C series features a standardized button layout for ease of use:
ON/OFF Button: Starts or stops the system with a single press.
Temperature Setting: Uses "Up" and "Down" arrows to adjust the setpoint, typically between 16∘C16 raised to the composed with power C 30∘C30 raised to the composed with power C Operation Mode Selector: Cycles through various modes: Cool: Snowflake symbol; lowers room temperature. Heat: Sun symbol; raises room temperature. Dry: Removes moisture without significant cooling. Fan Only: Operates the fan without heating or cooling. Daikin Brc4c160 Manual
Auto: Automatically switches between heating and cooling to maintain the setpoint.
Fan Speed Control: Toggles between Low, Medium, High, and Auto speeds.
Airflow Direction (Swing): Adjusts the vertical or horizontal louvers. Advanced Features
Programming Timer: Allows users to set specific "Start" and "Stop" times for automated operation.
Field Settings: Used by technicians to configure system parameters. Access this by holding the Test button for 4 seconds, then using the Mode and Temperature buttons to navigate codes.
Diagnostics: The remote can display error codes to help troubleshoot system faults. Maintenance and Troubleshooting
Error Codes & Resetting A Daikin - Peninsula Air Conditioning
To reset a Daikin fault, you must enter the diagnostic mode using the remote control to retrieve the fault code. Then, use the On/ Peninsula Air Conditioning The Daikin BRC4C160 is a wireless remote controller
Daikin BRC4C160 is a genuine wireless remote controller used to operate a wide range of Daikin air conditioning systems, including ducted and split units. It provides wireless infrared (IR) communication to control indoor units with a standard range of approximately 9 to 10 meters. www.daikinspareparts.com.au Key Control Features
The BRC4C160 manual outlines several core functions for managing your environment: OPERATION MANUAL SPLIT SYSTEM Ducted Air Conditioner
Some technicians have discovered “hidden” menus. While not in the standard user manual, these are documented in the service manual supplement.
A: This is normal. Check the manual’s explanation of "Thermostat ON/OFF" versus "Fan continuous operation." The indoor fan may be set to circulate air even when heating/cooling stops.
When the "Filter" icon appears, it means the unit has accumulated 2,500 operating hours. After cleaning the air filter, press the "Filter" button for 2 seconds (or use the combination in the manual) to reset the timer.
Your BRC4C160 has the following physical buttons (left to right, top to bottom):
| Button | Label | Primary Function | |--------|-------|------------------| | ON/OFF | (Power symbol) | Turns indoor unit on/off | | MODE | Mode | Cycles: Auto → Cool → Dry → Fan → Heat | | FAN | Fan | Changes fan speed (Auto, Low, Med, High) | | ▲ | Up (Temp) | Increases set temperature | | ▼ | Down (Temp) | Decreases set temperature | | TIMER | Timer | Accesses timer and schedule settings | | MENU | Menu | Enters main settings (Filter sign, Clock, etc.) | | CANCEL | Cancel | Exits current menu or cancels timer | | OK | OK/Select | Confirms selection |
Display icons explained in the manual:
If you are installing this unit yourself (though Daikin recommends a professional), the BRC4C160 Manual is explicit about the wiring: It uses non-polarized two-wire cabling. However, never run this communication wire in the same conduit as high-voltage power lines. The manual specifies a separation of at least 4 inches (100mm) to prevent electrical interference, which causes erratic "U4" or "U7" communication errors.
The BRC4C160 is a wired remote controller commonly paired with Daikin split systems, ducted units, and SkyAir commercial systems. Unlike a standard IR remote, this unit wires directly into the indoor unit, meaning you never lose it behind the couch, and it provides more diagnostic feedback.
The manual provides clear steps for daily use:
Turning On/Off
ON/OFF. The operation lamp (green) on the indoor unit will light.Changing Mode
MODE. Watch the display cycle: A (Auto) → ❄ (Cool) → 💧 (Dry) → (Fan only) → ☀ (Heat).Adjusting Temperature
▲ to increase, ▼ to decrease. Range is typically 16°C to 32°C (60°F to 90°F). In Auto mode, the set temperature is a target; the unit automatically chooses cooling or heating.Fan Speed
FAN. Each press changes: A (Auto) → L (Low) → M (Medium) → H (High). In Dry mode, fan speed is fixed to Low; in Auto mode, the unit decides speed.A: The manual does not have a one-button reset. You must cut power at the breaker for 10 minutes. To reset just the timer settings, press "Timer" and "Cancel" simultaneously for 10 seconds. “ ” (Leaf) – Energy-saving operation active