Hi Sharp Dvr Reset Password New File

To reset the password on your Hi Sharp DVR , try the following official and technical recovery methods: 1. Try Default Credentials

If the DVR is new or has been reset recently, try these common default login details: Username: admin Password: 123456, admin, or leave it blank 2. Use the "Retrieve Password" Feature (Dynamic Code)

Most modern Hi Sharp recorders include a built-in recovery tool on the login screen: Go to the Login interface on your DVR monitor. Click on Forget Password or Retrieve Password. Select the Dynamic Code or Dynamic Password option.

Take a photo of the dynamic code page or QR code that appears.

Email this photo along with your model and serial number to sales@hisharp.com.tw or your regional distributor to receive a temporary unlock code. 3. Hardware Factory Reset

If software methods fail, you may need to perform a hardware reset:

Reset Button: Check the back or the internal motherboard for a small push button. Press and hold it for approximately 35–40 seconds while the device is powered on until you hear a beep.

Battery Removal: Power off the unit, carefully remove the CMOS battery from the motherboard for a few minutes, power the DVR on and then off again, and reinsert the battery. This can sometimes reset the internal clock and password on older models. 4. Technical Support Contact

If you cannot generate a dynamic code, contact Hi Sharp directly through their Official Support FAQ or via email at sales@hisharp.com.tw.

Which Hi Sharp model are you using? I can give you more specific button locations if you have the model number. How to Reset DVR Password

To reset the password on a new Hi Sharp DVR , the most reliable "new" method involves generating a Dynamic Code

directly from the device's interface and contacting support for a temporary unlock key. Method 1: Dynamic Code Reset (Official Support)

For newer Hi Sharp models, follow these steps provided by the Hi Sharp FAQ Support Navigate to Login : Go to the login screen on your DVR. Retrieve Password : Click on "Forget Password" and then select "Retrieve Password." Get Dynamic Code : Click the "Dynamic Code" page. A unique code will appear on the screen. Contact Support

: Take a clear photo/screenshot of this Dynamic Code page and email it to sales@hisharp.com.tw along with your region, model number, and serial number. Enter Temporary Password

: Once you receive a reply with a temporary password, use it to log in and immediately set a new, secure password. www.hisharp.com Method 2: Standard Default Passwords

If your unit is fresh out of the box or has been recently factory reset, try these common Hi Sharp Default Passwords Other common defaults , or leaving the password field blank. www.hisharp.com Method 3: Physical Hardware Reset

If software methods fail, some models allow a hardware-level reset to factory defaults: External Reset Button

: Look for a small pinhole or button on the back or bottom of the DVR. Press and hold it for 30–60 seconds while the device is powered on. Internal Battery Removal

: For older or non-standard models, unplug the unit, open the casing, and carefully remove the CMOS coin-cell battery from the motherboard for several minutes. Reinserting it may reset the system clock and stored password data. Helpful Resources Manuals & Firmware

: You can download specific datasheets and manuals for your model (e.g., HS-HX series) from the Hi Sharp Support Downloads Third-Party Tools

: For generic H.264 HiSilicon-based DVRs, some users utilize the CCTV Password Tools

app to generate master passwords based on the device's displayed date. www.hisharp.com : After regaining access, set up a Security Question Reserved Email in the User settings to make future resets much faster. www.hisharp.com firmware update for your model to enable newer QR code reset features? How to Reset DVR Password

Hi-Sharp DVRs can be unlocked by using the "Forgot Password" function to generate a dynamic code for support, or by attempting a hardware reset via the CMOS battery, with default credentials often being username "admin" and password "123456" www.hisharp.com

. For security, configuring security questions or binding an email address is recommended to avoid future lockouts www.hisharp.com

. For detailed procedures and to download specific manuals, visit the Hi-Sharp Support Portal Hi-Sharp Download Center www.hisharp.com FAQ - Support | HI SHARP INTELLIGENCE

Getting locked out of your surveillance system can be a major security headache. If you've forgotten your credentials, this guide covers how to perform a Hi Sharp DVR reset password using the latest "new" methods for modern firmware. 1. Try Factory Default Credentials First

Before performing a hard reset, verify if your device is still using the manufacturer's original settings. While Hi Sharp systems often require a password setup upon first use, older models or recently reset units might use: Username: admin Password: 123456 (common for Hi Sharp) or leave it blank. Alternative Defaults: admin / admin or admin / 000000. 2. Use the "Forgot Password" Wizard

Modern Hi Sharp DVRs (especially those with the newer UI) have a self-service recovery option built directly into the login screen. Navigate to the Login Interface on your monitor. Click the Forgot Password or "?" icon.

Dynamic QR Code: A QR code will typically appear on the screen.

Mobile Recovery: Use the Hi Sharp mobile app (often "Hi Sharp" or a rebranded CMS app) to scan this code. hi sharp dvr reset password new

A temporary verification code will be sent to your registered email or mobile number. Enter this code into the DVR to unlock it and set a new password. 3. Hard Reset via Motherboard (Physical Method)

If your DVR isn't connected to the internet or you didn't set up a recovery email, you may need to perform a physical reset.

The Reset Button: Disconnect power, open the DVR casing, and look for a small "Reset" button on the motherboard. Hold this button for 15–30 seconds while plugging the power back in.

TP Pins: Some Hi Sharp boards use two metal contact points (often labeled J1, J2, or Reset). Carefully short these pins with a screwdriver while powering the unit on to trigger a factory wipe. 4. Serial Number & Super Password Generation

For older Hi Sharp systems without QR codes, recovery is based on the device's internal clock and serial number.

Note the Serial Number (found on the sticker or the login help screen) and the current Date/Time displayed on the DVR.

Contact Hi Sharp Technical Support or an authorized distributor.

They will use a Super Password Generator to provide a one-day master code based on your system's date. This code allows you to bypass the login once so you can navigate to the "Account" settings and update your credentials. 5. Reset via Browser (Web UI)

If you know the DVR's IP address and it is on your local network:

Open a browser (Internet Explorer mode is often required for older ActiveX plugins). Enter the IP address of the DVR.

On the login page, look for the Forgot Password link. If you previously configured Security Questions, you can answer them here to regain access instantly.

Pro-Tip: Once you've regained access, immediately navigate to System > User > Edit to set a strong, new password. Don't forget to update your recovery email address to avoid needing a hard reset in the future. How to Reset a NVR Without Password: Easy Guide - eufy US

Just locate the reset button on your NVR or DVR, then press and hold it for up to 30 seconds to start the resetting process.

How to Reset DVR to Factory Default without Password? - Reolink

To reset the password for a Hi Sharp DVR , use the following methods depending on your access level and model. 1. Use the Default Credentials

If this is the first time you are setting up the device, try the factory default credentials: www.hisharp.com 2. Physical Hard Reset (Motherboard)

For many older or standard Hi Sharp models, you can perform a hardware reset by interacting with the internal components: Internal Reset Button

: Open the DVR casing and look for a small push button on the motherboard. With the power on, press and hold this button for 10–30 seconds until the unit beeps or restarts. Battery Removal : Some users report success by removing the internal CMOS coin battery

for at least 30 seconds while the unit is powered off. This may clear the volatile memory holding the password. 3. Software & Dynamic Password Reset

If physical methods aren't available, use software tools to generate a temporary recovery key: Hi Sharp IP Finder : Download the Hi Sharp IP Finder software

to your PC. If the device is on your local network, you may be able to access recovery options through this tool. Dynamic Password : Click on "Retrieve Password" "Forgot Password"

on the DVR login screen. If it displays a "Dynamic Password" prompt or a QR code, you typically need to contact Hi Sharp Technical Support

with the displayed serial number or date to receive a one-day master code. Security Questions : If previously configured, select the "Edit Security Question"

option at login to reset the admin password by answering your pre-set questions. www.hisharp.com 4. Remote App Reset If your DVR is linked to a mobile application: How to Reset DVR Password

Phase 2: The Super Password Generator (The "Hash" Method)

If the defaults failed, you are likely looking at a screen that says "Login Failed" or shows a "Hash Code." This is the most common modern security feature for Hi-Sharp units.

When you enter the wrong password multiple times, the DVR will lock you out. On many Hi-Sharp interfaces, a string of characters (numbers or letters) will appear on the screen, often labeled as a Serial Number, MAC Address, or Hash Code.

This code is the key. It is a mathematical representation of the current time or the unit's hardware ID. Because the algorithm is known, developers have created "Password Calculators" that take this code and spit out a temporary master password.

How to use this method:

  1. Identify the Code: Look at the login screen. Write down the Serial Number or the Hash Code exactly as it appears.
  2. Download a DVR Password Calculator: Search for "Hi-Sharp DVR Password Calculator" or "Generic DVR Password Generator." Many of these units utilize the same chips as Hikvision or Dahua generic clones. A popular tool is the "CCTV Super Password" app available on Android phones, or various "Master Password" tools found on CCTV forums.
  3. Input the Code: Enter the Hash/Serial number into the generator.
  4. The Result: The generator will give you a temporary password (often a string of 8 numbers or letters).
  5. Login: Enter admin as the username and the generated code as the password.
  6. Change It: Once inside, immediately go to System Settings > Users and change the password to something you will remember.

Note regarding the Date: Some older Hi-Sharp algorithms rely on the system date. If the DVR has a dead CMOS battery, the date may have reset to 1970-01-01 or 2000-01-01. If your password calculator isn't working, try setting the date in the calculator to match the date shown on the DVR screen (if visible). To reset the password on your Hi Sharp

5. Contact Sharp support or an authorized technician

Method 3: Using Hi Sharp DVR Software

You can also use the Hi Sharp DVR software to reset the password. Here's how:

  1. Download and install the Hi Sharp DVR software on your computer.
  2. Launch the software and connect to your Hi Sharp DVR device.
  3. Go to the "Device Management" or "System Settings" section.
  4. Look for the "Password Reset" or "Change Password" option.
  5. Follow the on-screen instructions to reset your password.

New Hi Sharp DVR Models: Additional Reset Methods

Newer Hi Sharp DVR models may have additional reset methods, including:

5. Method 3 – Reset via Hi Sharp CMS Software (if previously added)

If you have Hi Sharp CMS (Central Management System) installed on a PC and the DVR was added before:

  1. Open CMS and go to Device Management.
  2. Right-click the DVR → Modify Password or Reset Device.
  3. Some versions allow a force reset without old password if the DVR is connected via LAN with admin rights.

2. Try Default Passwords First

Before resetting, try these common defaults:

If you changed it and forgot it, proceed below.

6. Preventive tips after reset

Note: Procedures vary by Sharp DVR model. If you provide the DVR model number (e.g., Sharp DVR-xxxx), I can give exact reset steps or codes.

To reset the password on your Hi-Sharp DVR, you can use the built-in "Dynamic Code" recovery or a physical hardware reset. Most Hi-Sharp devices default to a username of admin and a password of 123456. Option 1: Dynamic Code Recovery (Software)

If you are at the login screen and can't remember your password, follow these steps:

Navigate to Retrieve Password: On the login screen, click on "Forgot Password" and then select "Retrieve Password".

Generate Dynamic Code: Open the "Dynamic Code" page on your monitor.

Contact Support: Take a clear photo or screenshot of this page and send it to your regional distributor or directly to Hi-Sharp Support at sales@hisharp.com.tw.

Enter Reset Code: They will provide a temporary code you can enter to unlock the device and set a new password. Option 2: Hardware Reset (Physical)

If you cannot access the software menu, you may need to reset the unit to factory defaults physically:

Reset Button: Look for a small button or pinhole labeled "Reset" on the back or bottom of the DVR. Press and hold it for 10–30 seconds while the device is powered on until you hear a beep.

Motherboard Jumper: If there is no external button, you may need to open the case (ensure power is disconnected first). Look for two metal pins on the motherboard labeled G1 or Reset. Use tweezers to connect (short) these pins, then power the unit on and wait about 60 seconds before releasing.

CMOS Battery: As a last resort, removing the coin-sized CMOS battery from the motherboard for 5–10 minutes can sometimes clear saved settings and passwords. Common Default Credentials After a successful factory reset, try these default logins: Username: admin Password: 123456 or admin

Legitimate steps for Sharp DVR password reset (with authorization):

  1. Contact Sharp Support – Provide proof of ownership (serial number, purchase receipt)
  2. Default credentials – Try common defaults like admin / 12345 or admin / (blank) if never changed
  3. Hardware reset button – Some models have a physical reset button inside the unit
  4. Firmware recovery – Reflashing firmware may reset settings (requires manufacturer files)
  5. Recovery email – If configured, use "Forgot Password" option on the DVR interface

I cannot provide:

If you're locked out of your own device: Contact Sharp's security/support team directly with your ownership documentation. They will provide the official recovery procedure.

If you are locked out of your Hi Sharp DVR or security system, the reset process depends on your specific model and the software version it’s running. As of April 2026, most new Hi Sharp systems utilize "dynamic codes" or QR-based recovery rather than universal master passwords. 1. Use the "Dynamic Code" Method (Newer Models)

For most modern Hi Sharp units, you can generate a temporary code through their official support channels:

Step 1: Go to the DVR's login screen and click "Forget Password" or "Retrieve Password".

Step 2: Look for a button or tab labeled "Dynamic Code". This will generate a unique code or QR code on your monitor.

Step 3: Take a photo or screenshot of this screen and send it to sales@hisharp.com.tw or your regional distributor. Include your device's model number and serial number.

Step 4: They will provide a temporary password. Once you log in, go to Settings > User to set a permanent new password immediately. 2. Common Default Passwords (Legacy Models)

If your device is older or hasn't been set up yet, try these factory defaults (Username is almost always admin): 12345 or 123456 000000 or 0000 admin Leave the password field blank. 3. Physical Hardware Reset

If software methods fail, you can perform a factory reset via the motherboard:

External Reset: Check the back or bottom for a pinhole labeled "Reset." Press and hold with a paperclip for 10–30 seconds while the device is powered on until you hear a beep. Phase 2: The Super Password Generator (The "Hash"

Internal Jumper (Advanced): Power off the unit and open the case. Look for two metal pins labeled "J1" or "G1" (jumpers). Use a screwdriver or tweezers to bridge (connect) these two pins, then power the device on. Hold the bridge for 30–60 seconds to wipe the admin credentials. Troubleshooting Tips

Resetting Password of DVR/NVR by Scanning QR Code - Hik-Connect

Hi Sharp DVR units, resetting a forgotten password depends on the age of your device. Newer models typically utilize software-based recovery or "dynamic codes," while older units may require manual hardware intervention. 1. Default Login (First Time Setup)

If you are setting up a brand-new unit or have successfully factory reset it, try the factory default credentials: 2. Software Recovery (Newer Models)

Most modern Hi Sharp DVRs/NVRs feature a "Forgot Password" option on the login screen. Forgot Password on the local login screen. Navigate to Retrieve Password and select the Dynamic Code Take a photo/screenshot of the QR code or dynamic code displayed on the screen. Contact Support:

Email the photo along with your region, model number, and serial number to sales@hisharp.com.tw

or contact your regional distributor. They will provide a temporary reset key. 3. Hardware Reset (Internal)

If software methods are unavailable, you may need to perform a physical reset on the device's motherboard. FAQ - Support | HI SHARP INTELLIGENCE

Here are concise steps to reset a Sharp DVR password (assumes Sharp-brand DVR; steps may vary by model):

  1. Power-cycle and try defaults

    • Reboot the DVR (power off, wait 10–20s, power on).
    • Try default admin credentials: admin / 123456, admin / 000000, or admin / 888888.

  2. Use onboard reset button (if available)

    • Locate a small RESET pinhole or button on the rear/bottom.
    • With unit powered, press and hold the reset button for 10–30 seconds (use a paperclip). Release and reboot.

  3. Use DVR menu “Forgot password” or “Password reset” option

    • At the login screen, look for a reset/forgot link.
    • Follow on-screen instructions (may require answering security question or entering a reset code shown on screen).

  4. Use manufacturer master password (model-specific)

    • Some Sharp DVRs accept a manufacturer master reset code based on the device’s serial or a shown UID. Note the UID/serial shown after failed logins and contact Sharp support with that code.

  5. Restore firmware to factory (advanced)

    • Download official firmware for your exact model from Sharp support.
    • Follow firmware update instructions (often via USB) to restore factory settings — this will erase recordings. Only do this if other methods fail.

  6. Contact Sharp support or reseller

    • Provide model number, serial number, and UID (if shown). They can supply a master reset or service procedure.

Security notes:

If you give your DVR model number (printed on the unit) I’ll provide model-specific reset steps.

To reset the password for a Hi Sharp DVR (New Model), you can typically use the built-in "Dynamic Code" feature or the official password retrieval process. If your device is brand new or recently reset, the default login credentials are usually admin / 123456.

Method 1: Using the "Dynamic Code" (Recommended for New Models)

Newer Hi Sharp models include a self-service recovery option via the local interface. Navigate to the login screen on your DVR monitor. Click on "Forget Password" or "Retrieve Password".

Select the "Dynamic Code" page to generate a unique code or QR code on the screen. Take a screenshot or photo of this dynamic code.

Send the image, along with your model number and serial number, to your regional distributor or directly to Hi Sharp Support at sales@hisharp.com.tw.

They will provide a temporary recovery code to unlock the device and set a new password. Method 2: Initial Setup & Default Credentials

If you are setting up the DVR for the first time or after a successful factory reset, use these default settings: Username: admin Password: 123456

Action: Upon first login, you will likely be prompted by a Wizard Setup to create a strong, unique password. Method 3: Hardware Reset (If Software Fails)

For models where you cannot access the software reset menu, a physical reset on the motherboard may be necessary.

Internal Reset Button: Some units have a small button on the mainboard. Press and hold it for 5–10 seconds while the unit is powered on until you hear a long beep.

Jumper Pins: If there is no button, look for two metal pins labeled "TP" or "J1". Use a screwdriver or tweezers to short-circuit these pins while powering on the device. Hold for roughly 60 seconds to restore factory defaults. FAQ - Support | HI SHARP INTELLIGENCE

Note: Resetting will either restore factory defaults or require a master unlock code. This process typically deletes the old password but may also reset network and recording settings.

Method 4: Firmware Re-flash (The "Nuclear" Option)

If the hardware jumper doesn't work (some Hi Sharp models solder the password to the firmware), you must re-flash the firmware. This gives you a completely new operating system and wipes the old password.

  1. Download the correct firmware for your exact Hi Sharp model from their official support page.
  2. Format a USB flash drive to FAT32.
  3. Rename the firmware file to update.bin and place it in the root of the USB.
  4. Insert the USB into a port on the DVR.
  5. Power on the DVR while repeatedly pressing the ESC or Enter key on the mouse (or a USB keyboard).
  6. You will enter "BootLoader" mode. Select "Upgrade Firmware."
  7. Wait 10 minutes. Do not power off.
  8. After reboot, the password is reset to admin / 123456 – set a new one immediately.