How Do I Reset My Parrot Mki9200 Without Remote Best -

Review: Resetting the Parrot MKi9200 Without the Remote Rating: ★★☆☆☆

I recently bought a used car that had a Parrot MKi9200 already installed. The system worked fine, but the previous owner didn't leave the wireless remote control, and the Bluetooth was paired to their old phones, meaning I couldn't connect mine.

I spent hours online trying to figure out how to do a "hard reset" or factory reset using just the screen and the steering wheel controls. Here is the conclusion I came to:

The Bad News: It seems impossible to fully factory reset the MKi9200 without the remote. The "Settings" menu—where the "Restore Factory Settings" option lives—is navigable, but the specific reset function is often blocked or requires a specific key combination that only exists on the remote.

I tried holding down the jog wheel, combinations of the red and green buttons on the screen, and disconnecting the battery for an hour. None of it cleared the paired devices list.

The Workaround (How I fixed it): Since I couldn't reset the memory, I had to use the "Delete All Pairs" method, but you need a phone already connected to do it. Since I couldn't connect my phone, I was stuck. how do i reset my parrot mki9200 without remote

Eventually, I bought a cheap generic replacement remote on an auction site for about $15. The moment I put batteries in that remote, I was able to hold the red and green buttons down simultaneously to trigger the hardware reset.

Verdict: If you don't have the remote, you are essentially locked out of the system's administration functions. If you are in this situation, don't waste time trying button combos on the screen; just buy a replacement remote or check if your local car audio shop has a spare they can lend you for 30 seconds to wipe the memory.

Step 4: Observe the Screen

Keep holding the button while watching the Parrot screen. After a few seconds, the screen should change.

Method 1: The Pin-Hole Reset (Recommended)

This is the official hardware reset method and is the safest and most effective.

Step 1: Locate the Reset Hole Look at the back or the side of the small control screen (the color screen that shows the track info). You will find a tiny, circular pinhole no larger than 1mm across. It is often labelled "RESET" or has a small circular icon next to it. Review: Resetting the Parrot MKi9200 Without the Remote

Step 2: Power On the System Turn your car's ignition to the "Accessory" or "On" position so that the Parrot MKi9200 powers up and the screen lights up.

Step 3: Press and Hold the Reset Button Take your paperclip or pin, insert it straight into the reset hole, and press firmly until you feel a tactile click (like pressing a tiny button inside). Hold it down for approximately 10–15 seconds.

What to expect:

Step 4: Verify the Reset Once the system fully restarts, you will be greeted with the "Welcome to Parrot" voice prompt or a setup wizard. The unit will no longer remember your old phone. This confirms a successful factory reset.

Method 1: Use the Wired Control Pad (The Best Alternative)

The MKi9200 comes with a small, wired, button-style controller (often mounted near the gear stick). This is your lifeline when the rotary remote is missing. Step 4: Observe the Screen Keep holding the

Step 6: Power Cycle

Turn your car ignition completely OFF. Wait 30 seconds to ensure the capacitors in the Parrot unit fully discharge. Turn the ignition back ON.

Result: The Parrot MKi9200 should now boot up with the "Parrot" logo animation, followed by the language selection menu. This indicates the memory has been wiped and the device has been reset to factory defaults.

Step 3: The "Update Mode" Trigger

This is the most critical step.

  1. Take your paperclip and straighten it.
  2. Gently insert the paperclip into the hole and press the button. You should feel a distinct "click."
  3. Hold the button down.

Step-by-step:

  1. Locate the small LCD screen (the color display).
  2. Look on the back edge of the screen casing. You will find two very small, recessed buttons labeled "<<" and ">>" (previous/next track) or sometimes just two unlabeled tactile buttons.
  3. Press and hold both buttons simultaneously for about 10 seconds.
    • Note: You may need a paperclip or a pen tip to press them.
  4. Watch the screen. After 10 seconds, the screen should go blank and then show the Parrot logo (boot screen).
  5. Release the buttons.
  6. Result: The system has now performed a "cold reboot." This usually clears the current Bluetooth pairing list and resets the internal Bluetooth module. Your phone will no longer be connected, and you can pair a new device as if it were new.

Does this delete all settings?
No. It clears Bluetooth pairings and temporary cache. The equalizer settings, language, and voice tags will likely remain. To fully wipe those, you need the remote.