Kirisun Programming Software Pt8100 Here

To program the Kirisun PT8100, you need the specific Customer Programming Software (CPS) and a compatible USB programming cable. The PT8100 is a professional mobile radio that supports up to 256 channels and features like 2-Tone, 5-Tone, and DTMF signaling. 1. Requirements

Software: Kirisun PT8100 CPS (common versions include V1.28 or PT8100 12 1).

Hardware: A USB-to-serial programming cable (like the KSPL-05).

PC Drivers: Ensure your PC recognizes the cable. Many cables use Prolific chips that may require older drivers to function on modern Windows versions. 2. Setup and Connection

Install Software: Download the CPS from the Kirisun Download Center (note: some downloads may require a partner login) or use the installer provided by your vendor. kirisun programming software pt8100

Connect Cable: Plug the USB end into your PC and the radio connector into the accessory port on the radio.

Identify COM Port: Open Windows Device Manager, look under "Ports (COM & LPT)," and note the COM number assigned to your cable (e.g., COM3).

Power On: Ensure the radio is connected to a stable power source and turn it on. 3. Programming Steps Kirisun Programming Software Pt8100 12 1 - Facebook

Part 5: How to Program the Kirisun PT8100 (Walkthrough)

Now for the core task: programming channels. To program the Kirisun PT8100 , you need

1. Connect the Radio: Ensure the PT8100 is powered OFF. Connect the programming cable to the radio’s mic/speaker jack.
2. Launch the Software: Open the Kirisun PT8100 CPS.
3. Read the Radio: Go to Program > Read from Radio (or press F3). Turn the radio ON when prompted. The software will read the current codeplug (the radio’s brain). Always read first – never write a blank file to the radio.
4. Backup the Original Codeplug: Immediately save the read data as PT8100_Backup_Original.dat. If you mess up, you can revert.
5. Edit Channels:
   • Navigate to the Channel Information or Zone tab.
   • You will see rows for Channel 1, 2, 3, etc.
   • Rx Freq: Input the receive frequency (e.g., 462.562500).
   • Tx Freq: Input the transmit frequency (if duplex) or leave same as Rx for simplex.
   • QT/DQT Enc/Dec: Set your CTCSS (e.g., 67.0 Hz) or DCS code.
   • Power: Select High (4-5W) or Low (1W).
   • Busy Lock: Set to Carrier or QT/DQT to prevent channel interruptions.
6. Write to Radio: Click Program > Write to Radio (F4). Turn the radio off and on again as instructed.

Troubleshooting Write Errors: If you see "Communication Timeout," your COM port is wrong, or the cable driver is outdated. Try a USB 2.0 port (not USB 3.0), as legacy radios dislike USB 3.0 controllers.

Export Restrictions

Kirisun software sometimes contains encryption features (ARC4, AES). Exporting such software without a permit from your local trade authority may violate export control laws.

Why Can't You Manually Program It?

Unlike amateur radios or some consumer FRS/GMRS models, the PT8100 lacks a numerical keypad for direct frequency entry. All changes must be written to the radio’s codeplug (the internal memory file) via a Windows PC using the Kirisun programming software.

Part 10: Conclusion and Best Practices

The Kirisun Programming Software for PT8100 is a powerful, professional tool. When used correctly, it transforms a generic walkie-talkie into a tailored communication network. Part 5: How to Program the Kirisun PT8100

Part 2: Sourcing the Correct Kirisun Programming Software for PT8100

This is the most critical step. Using the wrong software can permanently corrupt your radio’s codeplug.

Step 3: Run the CPS Installer

1. Right-click the installer .exe or .zip file.
2. Select "Run as Administrator".
3. Follow the setup wizard. Accept the default installation path (C:\Program Files (x86)\Kirisun\PT8100).
4. After installation, do not launch the software yet.

3. System Requirements

| Component | Minimum | |-----------|---------| | OS | Windows 7, 8, 10, 11 (32/64-bit) | | CPU | Intel/AMD 1 GHz+ | | RAM | 2 GB | | Disk Space | 100 MB | | Port | USB (virtual COM) or legacy RS-232 | | Cable | KSP-USB1 or KSP-RS232 (Kirisun proprietary) |

Note: Some USB cables use Prolific PL-2303 or FTDI chips. Install correct drivers before connecting.

4. Installation & Setup Steps

1. Download or insert CD containing the PT8100 CPS (e.g., PT8100_CPS_v2.0.3.exe).
2. Run installer as Administrator to allow driver access.
3. Complete installation – default path: C:\Program Files (x86)\Kirisun\PT8100 CPS\
4. Connect the programming cable to the PT8100’s side microphone/programming port (GX16 8-pin aviation connector).
5. Power on the radio (12V DC required; programming is possible while radio is on but not transmitting).
6. Install USB drivers if prompted (check Device Manager for COM port number).
7. Launch the software – you will see a blank channel grid.