Skip to main content
Go to Previous Slide Go to Next Slide

Ksz80 Ob S4lv02 Datasheet | Direct Link

The keyword "KSZ80 OB S4LV0.2" does not refer to a standalone semiconductor component like a typical Ethernet transceiver. Instead, it is the identifying marking for a T-CON (Timing Controller) board typically used in Sony BRAVIA LCD televisions, most notably the Sony KDL-40R470A

The term "KSZ80" in this context is part of the board’s silk-screen assembly number, and it should not be confused with the Microchip KSZ8081 series of Ethernet PHYs, which share a similar prefix but serve entirely different functions. Overview of the KSZ80 OB S4LV0.2 T-CON Board

The T-CON board acts as the "brain" of the display panel. It receives video data from the television's main logic board (via LVDS cables) and translates it into the specific timing signals required by the Source and Gate drivers to activate the individual pixels on the LCD. Primary Application: Used extensively in the Sony KDL-40R470A and related 40-inch LED/LCD models.

Board Markings: KSZ80 OB, S4LV0.2, and often secondary identifiers like LJ94-25257D LJ94-25482B

Role in TV Repair: This board is the first suspect when a TV has sound but no picture, or shows vertical/horizontal lines and distorted colors. Technical Specifications and Connectivity

While a full "datasheet" in the semiconductor sense isn't public (as these are proprietary Sony/Samsung parts), repair technicians rely on the following technical characteristics: Specification Input Interface Dual-channel LVDS (Low-Voltage Differential Signaling) Compatible Screen Size 40-inch LED/LCD Panels Major ICs

Typically includes a Samsung or Sony proprietary timing controller chip Power Inputs 12V (VCC), VGH, VGL, and AVDD (Analog Supply) Status Indicators ksz80 ob s4lv02 datasheet

Surface-mount LEDs (on some revisions) to indicate power-good status Troubleshooting Common Faults

If you are searching for this board's datasheet to repair a faulty television, look for these common failure points:

SMD Fuse Failure: The most common issue is a blown surface-mount fuse (often labeled F1) near the LVDS connector. If this fuse is open, the board receives no power, resulting in a black screen despite a working backlight.

Gamma IC Failure: Distorted or "washed out" colors are often caused by a failing Gamma IC (AS15-F or similar) which manages the reference voltages for color accuracy.

VGH/VGL Voltage Issues: Using a multimeter, technicians check for VGH (typically +20V to +30V) and VGL (typically -5V to -10V). If these are missing, the screen will likely remain blank or display a slowly fading image. Where to Source Parts

Because these boards are specific to certain TV models, they are typically found as salvaged or refurbished parts rather than new retail items. You can find listings for this specific board on eBay or Kupindo. The keyword "KSZ80 OB S4LV0

Are you attempting to diagnose a specific display issue like a black screen or color distortion on your Sony TV? Kupindohttps://www.kupindo.com SONY panel KSZ80 OB S4LV0.2 - Kupindo.com (70628949)

Table_title: SONY panel KSZ80 OB S4LV0.2 Table_content: header: | Želi ovaj predmet: | 1 | row: | Želi ovaj predmet:: Stanje: | 1: Harry Electronicshttps://www.harryelectronics.com T.CON BOARD SONY KDL-40R470A KSZ80 OB S4LV0.2

Exam: KSZ80 OB S4LV02 — Advanced Technical Examination Instructions: Answer all questions. Show calculations and reasoning where applicable. Use SI units. Total points: 100.

Section A — Fundamental understanding (20 points)

  1. (5 pts) Give a concise functional summary (3–4 sentences) of a typical Ethernet PHY/switch IC datasheet, listing the main features you would expect to find.
  2. (5 pts) Explain the difference between a PHY, a MAC, and a switch IC. Give one example use-case for each.
  3. (10 pts) Describe the typical blocks shown in a block diagram of a multi-port Ethernet switch IC (e.g., MACs, PHYs, switch fabric, MDIO, CPU interface, VLAN engine, QoS). For each block, provide the primary function and at least one key parameter or register-related control.

Section B — Electrical characteristics & power (20 points) 4. (8 pts) A datasheet specifies VDD = 3.3 V ±5% and an absolute max of 3.6 V. Explain the difference between recommended operating range and absolute maximum ratings, and describe the risks of operating at the absolute max. 5. (6 pts) Given the device draws 250 mA from 3.3 V at full load, compute power dissipation. If the thermal resistance junction-to-ambient (RθJA) = 45 °C/W and ambient temperature is 50 °C, estimate junction temperature. State whether this is within typical maximum junction rating of 125 °C. 6. (6 pts) The datasheet lists IO voltage tolerant inputs up to 5 V and specifies input clamp current of ±20 mA when input exceeds VDD. Explain proper input protection design to prevent latch-up or damage when interfacing a 5 V signal to the device.

Section C — Timing, interfaces, and signal integrity (20 points) 7. (6 pts) Define the following timing terms usually found in datasheets: tR (rise time), tF (fall time), propagation delay, and setup/hold times. Give typical units and why each matters for high-speed Ethernet signaling. 8. (8 pts) The Ethernet Rx differential pair requires APL (allowed peak-to-peak) common-mode range and a specified differential impedance of 100 Ω. Explain PCB layout guidelines to maintain impedance and minimize reflections between the magnetics and PHY. 9. (6 pts) For an MDIO interface operating at 2.5 MHz, the datasheet specifies maximum tSU (setup) = 100 ns and tH (hold) = 50 ns. Draw or describe the timing window relative to the MDIO clock and explain consequences of violating those timings. (5 pts) Give a concise functional summary (3–4

Section D — Registers, configuration, and software (20 points) 10. (6 pts) A register map shows a control register at address 0x00 with bits: bit 15 = reset (self-clearing), bit 12 = speed select (0=10/100, 1=1000), bit 8 = loopback enable. Describe initialization sequence after power-up to enable Gigabit mode, bring the device out of reset, and enable auto-negotiation. 11. (8 pts) Explain how MDIO/MDC transactions read a 16-bit register: outline preamble, start, opcode, PHY address, reg address, turnaround, and data phases. Give the bit lengths for each field per Clause 22. 12. (6 pts) Provide a short algorithm (pseudocode) to poll link status with exponential backoff: check up to 6 times, starting delay 100 ms doubling each attempt, stop early if link is up.

Section E — Reliability, testing, and compliance (10 points) 13. (5 pts) List five reliability or compliance tests (e.g., ESD, thermal cycling, humidity, S-parameter channel test, EMI) that the datasheet might reference, and give one acceptance criterion for each. 14. (5 pts) Describe how to interpret an eye diagram and bit error rate (BER) spec in the datasheet when qualifying a 1000BASE-T PHY.

Section F — Application design and troubleshooting (10 points) 15. (5 pts) Given intermittent link loss at gigabit only, list five plausible hardware causes related to board design or component choices, and the diagnostic step to confirm each. 16. (5 pts) A recommended application schematic shows magnetics, termination resistors, and 0.1 μF decoupling caps near VDD pins. Explain placement and value rationale for decoupling and magnetics relative to the PHY.

Bonus (optional, 10 points) 17. (10 pts) Create a short lab exercise to characterize the device’s power consumption vs

I searched for “ksz80 ob s4lv02 datasheet”, but was unable to find a direct match in standard public datasheet databases (e.g., from Texas Instruments, Analog Devices, Microchip, Infineon, or major memory manufacturers).

Here’s a breakdown of what that part number likely indicates, and how you can find the correct datasheet.

Step 2: Download the Master Datasheet

Go to Microchip’s official website and search for:

Step 3: Compare Pin 1 Markings

OEMs sometimes disable standard JTAG or MII pins. The "S4LV02" might refer to a custom OTP (One Time Programmable) configuration loaded during manufacturing. In this case, the electrical characteristics, register maps, and timing diagrams are identical to the KSZ8081 datasheet. Only the strapping options (PHY address, LED modes) differ.

Finding the official datasheet or substitute parts

MENU CLOSE