Lenel Lnl3300m5 Installation Manual Upd Top -

Installation Guide for the Lenel OnGuard LNL-3300-M5 Intelligent System Controller

The Lenel LNL-3300-M5 is a high-performance Intelligent System Controller (ISC) designed as a "plug-and-play" upgrade for legacy M5 Bridge enclosures. It provides a modern gateway for transitioning older Casi-Rusco systems to the OnGuard security management platform without requiring a complete rewiring of the facility.

This guide covers the essential steps for a successful installation and initial configuration. 1. Hardware Overview and Specifications

Before beginning the physical installation, ensure your environment meets the necessary requirements: Power Input: 12 to 24 VDC ± 10%, 500 mA maximum.

Communication Ports: Primary Ethernet (10/100 Mbps) and two RS-485 ports.

Memory: 15 MB of available on-board memory for database storage.

Capacity: Supports up to 64 downstream devices (LNL-1300-M5, LNL-1100-M5, etc.). 2. Preparing for Installation

Backup Data: Before replacing an existing controller, ensure all database records from the legacy system are backed up.

Inspect the Enclosure: The LNL-3300-M5 is designed to fit the footprint of the legacy M5 / Micro5 controller. Verify that the standoffs in the existing enclosure are secure.

Static Discharge: Always wear a grounded ESD wrist strap when handling the controller board to prevent permanent damage to the circuitry. 3. Physical Installation Steps Step A: Mounting the Board

Place the LNL-3300-M5 onto the mounting standoffs within the M5 enclosure. Secure it using the provided screws. Ensure there is adequate clearance for wiring and that the board does not touch the metal sides of the box. Step B: Wiring the Power

Connect the 12-24 VDC power source to the power input terminals (Vin and GND).

Pro Tip: Use a dedicated, battery-backed power supply to ensure the controller remains operational during local power outages. Step C: Network and Serial Connectivity

Ethernet: Connect a standard Cat5e/6 cable to the RJ45 port for communication with the OnGuard server.

Downstream RS-485: Connect the existing M5 reader interface boards to the RS-485 ports (Port 1 and Port 2). Ensure proper termination if the LNL-3300-M5 is at the end of the communication line. 4. Configuring DIP Switches

The LNL-3300-M5 uses DIP switches to define the hardware address and communication settings: Switches 1-5: Used to set the hardware address (in binary).

Switch 6 & 7: Typically used for communication speed settings.

Switch 8: Often used for a "bulk erase" or factory reset function when toggled during power-up.

Refer to the specific revision of your LNL-3300-M5 silkscreen for the exact DIP switch table, as minor variations exist between firmware versions. 5. OnGuard Software Integration

Once the hardware is powered and wired, you must add it to the OnGuard interface: Open System Administration. Navigate to the Access Control tab and select Panels. Add a new panel and select LNL-3300 as the type. Enter the IP Address assigned to the controller.

Download the database to the panel to initialize communication. 6. Troubleshooting Common Issues

No Communication: Check the Link/Activity LEDs on the Ethernet port. Ensure the Subnet Mask and Gateway on the controller match your network segment.

Reader Offline: Verify the RS-485 wiring polarity (A vs B). If using legacy M5 boards, ensure they are addressed correctly within OnGuard.

Memory Error: If the database fails to download, perform a memory clear using DIP switch 8 and try again. lenel lnl3300m5 installation manual upd top

The LNL-3300-M5 is a robust solution for modernizing legacy infrastructure. By following these installation steps, you can ensure a stable and secure connection to your OnGuard ecosystem.

Here’s a structured, “good post” version of that title and idea, optimized for clarity and searchability:

Title: Lenel LNL-3300M5 Installation Manual – Updated Top Reference

Post:

Looking for the Lenel LNL-3300M5 installation manual? You’ve come to the right place.

This updated post highlights the key steps, wiring diagrams, and configuration notes for the LNL-3300M5 – a dual-reader interface module for Lenel’s NetBox or OnGuard access control systems.

Quick install overview:

Mounting – Securely mount the board inside a Lenel enclosure (e.g., LNL-1320). Use standoffs to prevent shorts.
Power – Connect 12–24 VDC to the PWR terminals. Ensure sufficient current for readers and locks.
Communication – Connect RS-485 to the host controller (LNL-1000 or LNL-2000). Set the correct baud rate (default 38,400).
Readers – Wire Wiegand or OSDP readers to Reader A and Reader B ports. Match data 0, data 1, ground, and optional LED/beep lines.
Inputs/Outputs – Use the on-board inputs for door contacts or REX. Relay outputs control locks or auxiliary devices.
Addressing – Set the module address via DIP switches (typically SW1). Ensure no duplicates on the same bus.
Firmware – Verify compatibility with your OnGuard version. Update via the LNL-3000 firmware loader if needed.

Pro tips:

Always power down before changing DIP switch settings.
For OSDP, use two-conductor shielded cable and enable OSDP in OnGuard hardware tree.
Test reader LEDs and beeper functions before finalizing installation.

Need the full PDF?
Lenel typically provides manuals through their partner portal. If you’re a certified integrator, check the “Product Documentation” section for the latest revision of the LNL-3300M5 installation guide (DOC# LNL-3300M5-INST-xx).

If you can’t access the portal, reach out to Lenel technical support with your company’s partner ID.

Last updated: [Insert date]
Let me know if you need specific wiring pinouts or DIP switch tables!

The Lenel LNL-3300-M5

is an intelligent system controller designed as a direct "plug-and-play" replacement for legacy CASI M5 and M3000 CPUs. It facilitates the migration of older systems like Picture Perfect to the modern Lenel OnGuard platform. Installation Highlights

Retrofit Design: The M Series boards are specifically designed to fit into existing CASI enclosures, requiring only a straightforward swap of the legacy boards with new Lenel hardware. Power Requirements: Operates on 12 or 24 VDC input power.

Connectivity: Features an on-board 10/100Base-T Ethernet port for high-speed upstream communication.

Memory & Storage: Includes 15 MB of non-volatile flash memory and supports up to 50,000 events in battery-backed storage. Step-by-Step Initial Configuration

Prepare Networking: Set your computer's IP address to the same range as the panel's default (typically 192.168.0.x), avoiding the specific default IP of the board.

Set DIP Switches: For initial web configuration, turn DIP switch 2 ON, while 1, 3, and 4 remain OFF.

Power Cycle: Turn the panel off and then back on. Wait roughly 30 seconds for the reboot.

Access Web Interface: Use a browser to navigate to the panel's default IP. To log in with the default credentials (admin/password), you must flip DIP switch 1 to ON while at the login screen.

Apply & Reboot: After configuring your static or DHCP settings, navigate to the "Apply Settings" page. This step is critical to commit changes to the panel's non-volatile memory. Maintenance & Firmware

Firmware Updates: Updates are stored in flash memory and can be downloaded in the background via the OnGuard software interface.

Health Monitoring: Status LEDs on the board provide immediate feedback on heartbeat, battery status, and communication activity. Access control 3300 lenel ip setup Title: Lenel LNL-3300M5 Installation Manual – Updated Top

Lenel LNL-3300-M5 is an Intelligent System Controller (ISC) designed specifically as a "plug-compatible" replacement for legacy CASI M5 and M3000 CPU boards, facilitating migration to the LenelS2 OnGuard security system. Key Specifications plus or minus 10% at 300 mA. Communications: 10/100 MB Ethernet (Host), RS-485 (Backplane/External).

Supports up to 240,000 local badge holders and 50,000 offline events. Compatibility:

Replaces CASI M5/M3000 CPUs (E, P, PX, PXN, PXNplus) and CASI Power/Comm Boards. Installation Steps Preparation:

Power down the legacy CASI controller and unplug all field wiring from the existing legacy boards.

Remove the legacy CASI CPU and Power/Comm boards from the backplane.

Insert the LNL-3300-M5 into the same slot on the M5/M3000 backplane. It is designed to be physically compatible with the existing footprint.

Plug the legacy 12 VDC power input, cabinet tamper, and AC power fail wires into the new board.

Connect the Ethernet cable to the onboard 10/100 MB port for host communication.

If converting to the Lenel M Series, all boards in the controller must be replaced; legacy CASI boards cannot be mixed with Lenel M Series boards. Initial Configuration & IP Setup To access the web configuration page for initial setup: Set Computer IP: Change your computer’s IP address to a range between 192.168.0.2 192.168.0.254 (excluding 192.168.0.251 Hardware Toggle: Set the board’s DIP switches: Switch 3 & 4:

Connect a crossover or standard Ethernet cable between the controller and your PC, then power on the unit. Web Access: Open a browser and navigate to

I’m unable to provide the full installation manual for the Lenel LNL-3300-M5 (likely a typo for LNL-3300-M5 or LNL-3300-M5E – the dual-reader interface module) due to copyright restrictions. However, I can give you a detailed summary of the key installation steps and official sources where you can obtain the complete manual.

The “M5” Distinction

The M5 revision introduced enhanced memory, faster processing, and improved UPD handling. It fully supports Lenel’s Open Supervised Device Protocol (OSDP) and legacy Wiegand, making it ideal for hybrid migrations.

Need Help with a Specific Step?

If you’re stuck on a particular part – e.g., RS-485 termination, addressing multiple modules, or firmware update error – let me know and I can give you a detailed, safe procedure without reproducing the entire copyrighted manual.

The Lenel LNL-3300-M5 Go to product viewer dialog for this item.

is a high-performance Intelligent System Controller (ISC) designed for advanced access control within the OnGuard system. Specifically engineered as a migration tool, this board provides a "plug compatible" replacement for legacy CASI M5 and M3000 controllers, allowing users to upgrade legacy systems to the modern OnGuard platform without rewiring field devices. Key Specifications and Hardware Overview LNL-3300-M5

serves as the central processing unit for the controller, managing real-time access decisions and communication with the host software. Power Requirements: Supports 12 or 24 VDC ( ±plus or minus

Memory: Includes 15 MB of on-board non-volatile flash memory and battery-backed storage for up to 50,000 events.

Capacity: Can support up to 32 board addresses and manage up to 64 downstream devices.

Communication: Primary communication is via a 10/100Base-T Ethernet port. It also features secondary ports for RS-485 or RS-232 communication. Installation and Migration Process The installation of the LNL-3300-M5

is primarily focused on replacing legacy boards in an existing M5 or M3000 backplane.

Power Down: Safely power off the legacy controller and disconnect all power sources. Unplug Field Wiring

: Remove the wiring from the legacy CPU and Power/Comm boards.

Board Replacement: Remove the legacy CASI boards and insert the LNL-3300-M5 . It is designed to fit standard mounting standoffs. Mounting – Securely mount the board inside a

Reconnect Wiring: Plug field wiring back into the compatible terminals on the LNL-3300-M5

Grounding: Ensure the board is properly grounded to protect against Electrostatic Discharge (ESD) and signal transients. Initial Web Configuration and IP Setup

To configure the controller for the first time, you must access its internal web configuration page.

Network Preparation: Set your computer's IP address to the 192.168.0.x range (excluding .251) to match the panel's default IP of 192.168.0.251. DIP Switch Settings:

To enter configuration mode: Set DIP switch 1 OFF, 2 ON, 3 OFF, and 4 OFF, then cycle power.

To enable default login: Once at the login screen, turn switch 1 ON to use the default credentials (username: admin, password: password).

Access: Open a web browser (Internet Explorer is traditionally recommended) and navigate to http://192.168.0.251.

Save and Reboot: After applying static IP or DHCP settings, return all DIP switches to the OFF position (normal operating mode) and click Apply Settings and Reboot. DIP Switch Reference Table Operating Mode Normal operating mode Enable default User Name/Password Use factory default communication parameters

Lenel LNL-3300-M5 is an Intelligent System Controller designed specifically for migrating legacy CASI M5 and M3000 systems to the Lenel OnGuard platform. It acts as a direct "plug-compatible" replacement for legacy CASI CPUs and power/communication boards. Key Technical Specifications Operating Voltage: 12 to 24 VDC (± 15%). Current Consumption: 500 mA maximum.

Supports up to 32 board addresses and can store up to 50,000 events in non-volatile memory. Communication:

On-board 10/100 Ethernet for host connection and RS-485 for downstream device communication. Hitron Bina Teknolojileri Installation Steps Hardware Migration:

Power down the legacy controller and unplug all field wiring from legacy boards. Remove the legacy CASI CPU and Power/Comm Board. Insert the LNL-3300-M5 into the backplane and reconnect the field wiring.

Position the module over corresponding spacers in the enclosure and depress until it snaps into place.

Connect dedicated inputs for cabinet tamper (TMP) and power failure (FLT) status. Wiring Requirements: Use 18 AWG twisted pair.

Use 24 AWG twisted pair(s) with shield, up to a maximum distance of 4,000 ft (1,219 m). Initial Configuration & Web Setup

To initially configure the LNL-3300-M5 via its web configuration page: DIP Switch Settings:

Set DIP switch 1 OFF, 2 ON, 3 OFF, and 4 OFF to enable the default configuration. Default IP Address: The panel defaults to 192.168.0.251 Computer Setup:

Configure your computer's IP address to the 192.168.0.x range (excluding .251).

Lenel LNL-3300-M5 is an Intelligent System Controller (ISC) designed specifically as a plug-compatible replacement for legacy CASI M5 and M3000 CPU boards, facilitating a seamless migration to the OnGuard security system. Hitron Bina Teknolojileri Installation & Configuration Overview

To install and initially configure the LNL-3300-M5 via its web interface, follow these standard procedural steps: DIP Switch Setup

: Before powering up, set the S1 DIP switches to specific positions to enable the web configuration mode. For standard initial setup, turn DIP switch 1 OFF, 2 ON, 3 OFF, and 4 OFF Network Connection

: Connect the LNL-3300-M5 to a computer via the onboard Ethernet port. Configure the computer’s IP address within the 192.168.0.x range (e.g., 192.168.0.2 ), avoiding 192.168.0.251 , which is the default for the controller. Access Web Page

: Power on the unit and wait approximately 30 seconds for it to reboot. Browse to

How to Update Firmware (The UPD Standard Method)

Download the correct .enc file (e.g., LNL3300M5_v2.1.8.enc) from the portal.
Connect your laptop to the same Layer 2 network as the controller.
Open a web browser and navigate to https://192.168.0.250:8443 (Note the HTTPS and port 8443).
Log in and navigate to Maintenance > Firmware Update.
Upload the .enc file. Do not power cycle during the update—the board will reboot automatically (approx. 3 minutes).
Verify the update via Status > Firmware Version.

UPD Top Critical Warning: If you are deploying 20+ LNL-3300M5 units, use the Lenel Device Administrator (LDA) tool for batch updates. Manual web updates are only for single units.

Mapping Inputs and Outputs

Input 1 (DPS): Map to “Door Contact” for Door 1.
Input 2 (REX): Map to “Request to Exit” for Door 1.
Relay 1: Map to “Door Strike” for Door 1.