Pinout Top !exclusive!: Simos 33aCombines fuel injection, ignition timing, and electronic throttle control (EPC). Communication: interface for diagnostics via tools like VAG 1551 or VAS 5051. Components: Interfaces with the G28 Engine Speed Sender, Hall Sender (G40), and multiple Coolant Temperature Senders (G2, G62). For a detailed visual of the "top" view or specific PCB soldering pads, technicians often refer to Simos ECU Connection Guides on Scribd Skoda Fabia Simos 3 Pinout Guide troubleshoot a specific sensor issue? simos 33a pinout top Simos 7.1 Pinout and Installation Guide | PDF | Fuel Injection The Connector LayoutWhen looking at the ECU with the connectors facing you and the mounting tabs at the top, the plugs are usually arranged from left to right. Below is a breakdown of the critical pins found in the standard layout. Note: Pin locations can vary slightly between hardware revisions. Always look for the pin numbers stamped on the ECU plastic housing next to the connector slots. The Connector Layout When looking at the ECU Conclusion: Your Top-Side Reference GuideThe Simos 33A pinout top view is an essential map for anyone diagnosing, tuning, or repairing modern VAG ECUs. By understanding the physical layout—identifying power headers, CAN transceivers, and test points—you can confidently probe the ECU on your bench or in the vehicle. Final checklist before probing the top side:
While this guide covers the 80-pin generic configuration, always cross-reference with official VAG wiring diagrams (ErWin) or a verified pinout for your specific ECU part number (e.g., 04E906033, 04L906033). Happy diagnosing, and may your signals be clean and your grounds be true. ✅ Disconnect the battery if probing inside a car Have a correction or addition for the Simos 33A top pinout? Leave a comment below or contact our technical team for a deep dive into your specific variant. Key Pinout Table (Top View – most useful for probing from top):| Pin | Function | Signal Type | Notes | |-----|----------|-------------|-------| | 1 | Ignition coil output (cyl 1) | Output | Low side driver | | 2 | Injector output (cyl 1) | Output | Saturation driver | | 3 | Injector output (cyl 2) | Output | | | 4 | Injector output (cyl 3) | Output | | | 5 | Injector output (cyl 4) | Output | | | 6 | Fuel pump relay control | Output | Grounds relay coil | | 7 | Lambda probe heater (front) | Output | Ground side | | 8 | Throttle valve position sensor (TPS) ground | Sensor Ground | | | 9 | TPS signal (wiper) | Input | 0.5-4.5V | | 10 | TPS 5V supply | Output | +5V reference | | 11 | Intake air temp (IAT) signal | Input | | | 12 | Coolant temp (ECT) signal | Input | | | 13 | MAP sensor signal | Input | Manifold absolute pressure | | 14 | MAP sensor 5V supply | Output | | | 15 | MAP sensor ground | Sensor Ground | | | 16 | Ignition coil output (cyl 2) | Output | | | 17 | Ignition coil output (cyl 3) | Output | | | 18 | Ignition coil output (cyl 4) | Output | | | 19 | +12V main relay output | Power | To sensors/actuators | | 20 | +12V permanent (battery) | Power | Direct from battery | | 21 | +12V from main relay | Power | ECU main supply | | 22 | Ground (power) | Ground | High current | | 23 | Ground (power) | Ground | High current | | 24 | Ground (sensor) | Sensor Ground | | | 25 | CAN High (if equipped) | Comm | Drivetrain CAN | | 26 | CAN Low (if equipped) | Comm | | | 27 | Knock sensor 1 signal | Input | | | 28 | Knock sensor 2 signal | Input | | | 29 | Crank position sensor (CKP) signal | Input | 60-2 wheel | | 30 | CKP sensor ground | Shield/Ground | | | 31 | Cam position sensor (CMP) signal | Input | Hall effect | | 32 | CMP sensor supply | Output | +5V or +12V | | 33 | CMP ground | Ground | | | 34 | Lambda probe signal (front) | Input | 0-1V narrowband | | 35 | Lambda probe ground (front) | Ground | | | 36 | Vehicle speed sensor (VSS) | Input | | | 37 | Brake light switch signal | Input | | | 38 | Clutch switch signal | Input | | | 39 | A/C request signal | Input | | | 40 | A/C compressor enable | Output | | | 41 | EPC warning lamp | Output | | | 42 | Check engine lamp (MIL) | Output | | | 43 | Diagnostic K-line (ISO 9141) | Comm | | | 44 | Idle air control (IAC) - close | Output | Stepper motor coil | | 45 | Idle air control (IAC) - open | Output | Stepper motor coil | | 46 | EVAP purge valve control | Output | | | 47 | Secondary air injection (SAI) relay | Output | | | 48 | Oxygen sensor heater (rear) | Output | If present | | 49 | Idle air control (IAC) - coil B | Output | | | 50 | Idle air control (IAC) - coil A | Output | | | 51 | Not used | - | | | 52 | Not used | - | | | 53 | +12V switched (e.g., from alternator) | Input | Load signal | | 54 | Power ground | Ground | | | 55 | Power ground | Ground | | | 56 | Sensor ground | Ground | | | 57 | Ignition switch input (Terminal 15) | Input | +12V when key ON | | 58 | Start signal (Terminal 50) | Input | +12V during cranking | | 59 | Engine speed output (to tachometer) | Output | Low side driver | | 60 | +12V backup (for adaptive memory) | Power | Permanent | Mastering the Simos 33A ECU: A Comprehensive Guide to the Top-Side Pinout |
