Sltouch For Sl1000 Exclusive Download Install [OFFICIAL]

To install SL-Touch for the SL1000 Digital Microfilm Scanner

, follow this guide to set up the specialized acquisition software used for digitizing microfilm, microfiche, and aperture cards. 1. Pre-Installation Requirements System Compatibility

: Ensure your PC is running a compatible version of Windows (the SL1000 typically uses standard Windows-based drivers).

: Secure a well-ventilated area for the scanner with at least the recommended clearance for operation.

: Use a stable power source with minimal voltage fluctuations. 2. Download and Software Installation sltouch for sl1000 download install

is proprietary software typically bundled with the hardware, follow these steps to obtain and install it: Installation Media

: Use the SL-Touch software CD/USB supplied as standard with the unit. Authorized Download : If you lack the physical media, contact your NEC Authorized Supplier or visit the official support portal (e.g., ) for the latest digital installer. Running the Setup Insert the media or open the downloaded folder. or installation file.

Follow the on-screen prompts to install the acquisition software and necessary drivers. 3. Hardware Connection Connect Scanner

: Plug the SL1000 scanner into the PC using the provided interface cable. : Turn the scanner ON using the main power switch. Carrier Setup To install SL-Touch for the SL1000 Digital Microfilm

: If using a motorized roll film carrier, ensure it is properly seated and recognized by the software. scan-pro.ru 4. Configuring SL-Touch Custom Interface

: SL-Touch features a customizable UI ideal for libraries or public kiosks. Initial Setup Open the application and navigate to the Environment

to verify that the scanner and PC are communicating correctly. Scan Settings

: Configure your default output format (JPEG, PDF, TIFF, etc.) and resolution (up to 600 dpi) within the software settings. 5. Firmware Updates (Optional) Step 4: Connect to the SL1000

If you need to upgrade the firmware to match a newer version of SL-Touch: Open the SL1000 acquisition software. Select the folder from the downloaded update package.

Follow the prompt to "Turn OFF" and then "Restart" the main unit to finalize the update. Yokogawa Electric SL1000 Digital Microfilm Scanner

6. Troubleshooting Common Issues

Step 5: Post-Installation Reboot

Reboot your PC. This ensures the TAPI driver loads at system boot.

Step 4: Connect to the SL1000

• Click Connect (or Online) button.
• If successful, SLTouch will read mailbox names, messages, and system prompts.
• If it fails, check:
  • Cable is null-modem (pins 2 & 3 crossed)
  • No other program is using the COM port
  • SL1000 serial port is enabled in system programming (Memory Block 10-03)

On the NEC SL1000 (via PCPro or WebPro):

1. Log into SL1000 programming (default IP: 192.168.0.10 / user: INSTALL / pwd: 12345678).
2. Navigate to 10-03 (SMDR Basic Configuration) :
   • Output Port: Set to 1 (Internal SMDR) or 0 (RS-232).
   • Format: 1 (Standard).
3. Enable SMDR for Extensions (20-13) : Ensure the extensions you want to log have SMDR Output = 1 (Enable).
4. If using IP connection (10-05) :
   • Set SMDR over IP = 1.
   • TCP Port Number = 8000 (default).
5. Write the system (F1 or Write button).

4.2 Execution

1. Locate the downloaded archive (e.g., SLTouch_V2.8_Setup.zip) and extract it.
2. Run the setup.exe file.
3. User Account Control (UAC): Click "Yes" to allow the program to make changes to the device.

Part 7: Common Installation Errors and Fixes

Even with careful steps, things go wrong. Here is your troubleshooting cheat sheet.

| Error Message | Likely Cause | Solution | | :--- | :--- | :--- | | "Cannot open COM port" | Another application is using the COM port (e.g., PCPro) or incorrect permissions. | Close PCPro. Go to Device Manager -> COM Port Properties -> Advanced -> uncheck "Serial Enumerator". Run SLTouch as Admin. | | "TAPI initialization failed" | .NET Framework missing or TAPI not registered. | Open CMD as Admin. Run regsvr32 tapi32.dll. Then re-run SLTouch TAPI installer. | | "No SMDR data received" | Wrong baud rate, wrong IP port, or SMDR disabled on SL1000. | Double-check 10-03 and 10-05 settings on SL1000. Use a terminal emulator (PuTTY) to verify raw SMDR output first. | | "Database connection error" | MySQL service not running, or wrong ODBC DSN. | Open Services.msc -> Start MySQL. Recreate System DSN in ODBC Data Sources (32-bit). | | "License file invalid" | Wrong version or host ID mismatch. | SLTouch licenses are often tied to the PC’s MAC address or hard disk serial number. Contact your vendor to reissue license. |

6. Troubleshooting Common Errors