Ts1162 Installation Manual _hot_ ❲Direct × 2027❳

Power Off: Ensure all power is disconnected from the Challenger panel or Intelligent Access Controller before starting any wiring to prevent damage.

Unpack: Verify the device for any physical damage and ensure all mounting hardware is present.

Location Selection: Choose a flat, vertical surface for mounting to prevent the base from flexing when tightened. 2. Mounting the Base

Disassemble: Remove the two retaining screws from the bottom of the keypad body and pull the bottom away from the base to disengage the top tabs.

Template: Use the base as a template to mark screw holes and the rear cable entry point (if using rear entry).

Secure: Use appropriate screws or bolts to mount the base to the surface. Ensure the tamper lever will be properly depressed against the surface when mounted to avoid constant tamper alarms. 3. Addressing and Configuration

Before completing the installation, you must set the device's unique address and termination on the internal DIP switches:

Device Address: Use DIP switches 1 through 4 to set the RAS address required for the Challenger system.

LAN Termination: If this keypad is the last device on the RS-485 LAN run, set DIP switch 8 to the "On" position to terminate the line. 4. Wiring and Termination ts1162 installation manual

LAN Connection: Connect the keypad to the Challenger RS-485 LAN (up to 1.5 km away) using standard security cabling.

Request to Exit (RTE): Use the dedicated input for RTE control if required for the door.

Door Control: The open collector output can be used to drive a door relay or door strike.

Cable Routing: Avoid wire loops inside the enclosure and ensure cables do not lie directly on the circuit board. 5. Final Assembly

Hook Body: Place the top of the keypad body onto the mounting tabs of the base.

Secure: Swing the bottom into place and replace the two retaining screws at the bottom to lock the assembly. Maintenance Tips

Cleaning: Use a soft, dry cloth. For stubborn marks, use a small amount of isopropyl alcohol. Avoid water, ketones, or aromatic solvents.

Protection: Do not use sharp objects on the keypad surface; use fingers or gloved hands only.

For further technical documentation, you can visit the Aritech Support Portal for official Tecom manuals. TS1020 Analogue Data Gathering Panel Installation Manual The Tecom TS1162 is a 3-LED Remote Arming

Tecom TS1162 is a 3-LED Remote Arming Station (RAS) keypad used with the Challenger

security system. It is specifically designed for harsh or wet environments, featuring a robust construction and an IP67 rating Ness Corporation General Installation Steps

While technical manuals for Tecom hardware are often restricted to trained installers on the Aritech portal

, the general installation procedure for Challenger RAS devices includes: support.firesecurityproducts.com.au Preparation

: Power down the Challenger panel before beginning any wiring.

Unscrew the retaining screws and remove the body assembly from the base.

Use the mounting template to mark screw holes and cable entry on the surface. Ensure the tamper lever will be depressed when the unit is mounted. Connect the device directly to the Challenger RS-485 LAN Data/Power

: Use the standard Challenger LAN terminals (+, –, D+, D-). For runs over 100 meters, a separate 12V power supply is recommended. Inputs/Outputs : The TS1162 includes a Request to Exit (RTE) input and one open collector output for controlling door relays or strikes. Addressing & Configuration RAS address using the internal DIP switches (typically switches 1–4).

Set LAN termination (DIP switch 8) if the device is at the end of a LAN run. Final Assembly which includes error code tables (e.g.

: Hook the top of the body onto the base and secure it with the retaining screws. Ness Corporation Key Features Connectivity : Can be placed up to from the Challenger panel or Intelligent Access Controller. Protection , making it suitable for dusty or outdoor applications.

: Features 3 LED status indicators rather than a full LCD screen. aritech.com.au

For full configuration and programming, you may need to access the ChallengerPlus Installation and Programming Manual or contact Aritech Technical Support for restricted documents. support.firesecurityproducts.com.au or details on how to program the door output for this keypad? Remote Arming Station (RAS) Keypad, 3 LED - Aritech

Remote Arming Station (RAS) Keypad, 3 LED * Robust moulded plastic housing. * Indoor or outdoor mounting. * Request to Exit input. aritech.com.au Tecom TS1162 3 LED RAS - Ness Corporation

6. Sensor Calibration (Mandatory)

Section 8: Where to Find the Official TS1162 Installation Manual

This guide is not a substitute for the official document. To obtain the genuine TS1162 installation manual:

1. Manufacturer’s website – Look under “Support” → “Downloads” → “Manuals”.
2. QR code on device – Some TS1162 units have a label with a QR code linking directly to the latest manual revision.
3. Authorized distributor – Contact your vendor with the batch number.
4. Manual library databases – Sites like ManualsLib or manualzz.com (verify edition date).

Warning: Avoid “free manual” sites that ask for credit card information. The TS1162 manual is typically provided free of charge by the manufacturer.

5. Electrical Wiring (Diagram A-3)

Overview

The TS1162 is a rack-mountable 1U network appliance (assumed model for this manual). This document covers unpacking, safety, hardware installation, rack mounting, cabling, initial power-up, basic configuration, and troubleshooting. Assume typical enterprise network environment; adapt to your site’s policies and power/grounding requirements.

7. First Boot & Setup

9. Common Installation Problems & Solutions (Troubleshooting)

Even with a proper TS1162 installation manual, issues can arise. Here are the top five:

| Problem | Likely Cause | Solution | |---------|--------------|----------| | Printer not detected | USB cable loose or wrong port | Try a different USB port or cable. Ensure cable is data-capable. | | Wi-Fi connection fails | Wrong password or router channel | Re-enter password. Change router to 2.4 GHz band. | | Ink error after install | Orange cap still on cartridge | Remove the orange cap. Clean electrical contacts. | | Paper jam | Paper too thick or curled | Use standard 80 gsm paper. Fan the stack before loading. | | Driver install freezes | Antivirus blocking | Temporarily disable antivirus. Run installer as administrator. |

For persistent errors, consult the full TS1162 installation manual PDF, which includes error code tables (e.g., E05 = no ink, E13 = paper jam).

7. Wireless Network Setup (Wi-Fi)

For cable-free printing, the TS1162 installation manual recommends using the WPS (Push Button) method.