Xinje - Plc Usb Driver Install New!

To install the USB driver for a , you typically need to install the COM-USB driver from the official Xinje website or ensure it is bundled with your programming software (like XDPPro or XCPPro). This driver allows your PC to recognize the USB-to-RS232 programming cable used for communication. Step-by-Step Installation Guide Download the Driver: Visit the official Xinje Download Center

and look for the COM-USB driver or the specific driver for your series (e.g., XC, XD, or XL series). Alternatively, drivers for older devices like the Xinje TH USB Device

can sometimes be found through specialized driver repositories. Connect the Hardware: Plug your USB programming cable into your computer.

Note that many Xinje PLCs use a USB-XC cable, which is a USB-to-RS232 adapter with an 8-pin round head for the PLC port. Run the Installation:

Locate the downloaded .rar or .zip file, extract it, and run the setup file (often an .exe) with administrative rights. Follow the on-screen wizard to complete the installation. Verify in Device Manager: Open Device Manager on your Windows PC.

Look under "Ports (COM & LPT)" to find the newly assigned COM port number (e.g., COM3 or COM6).

If you see a yellow exclamation mark, right-click the device and select "Update driver," then browse to the folder where you extracted the driver files. Configure Programming Software:

Open your software (e.g., XDPPro for XD/XL series or XCPPro for XC series). Go to Option > Software Serial Port Config. Select the correct COM port identified in Step 4.

Click Comm-Test. If successful, you will see a message like "Connect To PLC Succeeded". Troubleshooting Tips

Administrative Rights: Always run the installer as an administrator to ensure Windows doesn't block the driver files.

Cable Check: Ensure you are using the correct cable for your series. The USB-XC cable is the standard for most XC, XD, and XL models.

Auto-Detection: If the connection fails, many Xinje software tools have an "Auto-detect" button in the communication settings that can scan available ports for you. Download Center - Wuxi Xinje Electric Co., Ltd.

Step 2: Install the Driver

Part 7: Software-Specific Configurations

Troubleshooting Common Issues

By following these steps, you should have your Xinje PLC successfully communicating with your PC, ready for programming and debugging.

How to Install Xinje PLC USB Drivers: A Step-by-Step Guide Successfully connecting your PC to a Xinje PLC is a critical first step for programming, monitoring, and debugging industrial automation systems. This process typically involves installing two key components: the programming software (like XDPPro) and the specific USB-to-Serial drivers required for your communication cable. 1. Pre-requisites and Software Downloads

Before starting the installation, ensure you have the correct software for your PLC series. For most modern Xinje PLCs (XD/XL series), the standard tool is XDPPro, while older XC series may use XC Pro.

Download Center: Access official software and manuals directly from the Xinje Download Center.

Driver Files: Modern versions of XDPPro (e.g., v3.7 or v3.8) often bundle the necessary communication drivers, but separate driver files like xnetusb.inf or Silicon Labs Virtual COM Port (VCP) drivers may be required depending on your specific cable. 2. Installing the Xinje Programming Software

The USB driver installation is often part of the broader software setup. Follow these steps to install the primary programming environment: xinje plc usb driver install

Run the installer (e.g., XDPPro_Ver3.8.0.exe) as an administrator.

Follow the setup wizard prompts to select your destination folder.

Crucial Step: After the main software installation, you must often install the XNet Setup (e.g., XNetSetup_en.exe). This package frequently contains the underlying communication drivers and virtual COM port settings needed for USB connectivity. 3. Connecting the Hardware and Driver Verification

Once the software is installed, you need to verify that Windows recognizes your programming cable.

Connect the Cable: Plug your USB programming cable into your PC and the circular DIN port on the Xinje PLC.

Check Device Manager: Right-click "This PC" (or "My Computer"), select Manage, then Device Manager.

Identify the Port: Look under Ports (COM & LPT). You should see a "USB-Serial CH340," "Silicon Labs CP210x," or "Xinje TH USB Device" listed with a assigned COM port number (e.g., COM3 or COM6).

If you see a yellow exclamation mark (⚠️), right-click it, select Update driver, and browse to the installation directory of your Xinje software (usually C:\Program Files (x86)\Xinje...). 4. Configuring Communication in XDPPro

After the driver is active, you must tell the software which port to use. Open XDPPro and go to the Option menu.

Select Software Serial Port Config (or Communication Configuration).

Choose the COM port that matches the one identified in your Device Manager.

Click Comm-Test. If successful, a message stating "Connect To PLC Succeeded" will appear in red text. Troubleshooting Tips Download Center - Wuxi Xinje Electric Co., Ltd.

To install the USB driver for a Xinje PLC, you typically need to install the specific programming software for your PLC series, which often includes the necessary drivers automatically 1. Download Required Software

The driver you need depends on your PLC model and connection method: XD/XL Series: Download and install

(e.g., version V3.8.0). During the installation of XDPPro, the system will prompt you to install the USB driver XINJEConfig software automatically. XC Series: Download and install

(e.g., version v3.3r). If you are using a USB-XC programming cable, the driver is often based on the 2. Manual Driver Installation

If the driver does not install automatically or the device appears as "Unknown" in Device Manager Connect the PLC:

Power on the PLC and connect it to your PC via the USB or USB-to-RS232 cable. Open Device Manager: Right-click the Start button and select Device Manager Update Driver:

Locate the device (often under "Other devices" or "Ports"). Right-click it and select Update driver Browse Local Files: Browse my computer for drivers To install the USB driver for a ,

. Navigate to the installation directory of your Xinje software (e.g., C:\Program Files (x86)\XINJE ) to locate the driver subfolder. 3. Verification and Port Settings Check COM Port: Once installed, the device should appear under Ports (COM & LPT)

as a "USB Serial Port" followed by a COM number (e.g., COM3). Port Limit: Ensure the assigned COM port number is COM20 or lower

. If it is higher, you may need to manually change it in the Port Settings Advanced properties to avoid connection issues. Software Config: In your programming software, go to Option > Software Serial Port Config

and select the matching COM port to establish a successful connection. Further Exploration

Access official manuals and the latest software versions directly from the Wuxi Xinje Download Center Review the USB-XC Cable Manual for specific wiring and chipset details (CH340). Follow a step-by-step Xinje PLC Connection Tutorial to see the software configuration in action. Are you having trouble with a specific PLC model or encountering a particular error message during the installation? Download Center - Wuxi Xinje Electric Co., Ltd.

To install the USB driver for your , you typically need the XDPPro or XC Pro programming software, as the drivers are often bundled with these tools. 📥 1. Download Official Drivers

The most reliable source for drivers is the Xinje Download Center.

XDPPro Software: Most modern XD and XL series PLCs use this software, which includes the necessary USB communication drivers.

COM-USB Driver: A standalone "COM-USB driver" is also available on the official site for specific converter cables. USB to RS232 Driver | USB Serial Driver Downloads and Tools

Installing a Xinje PLC USB driver is the "handshake" that lets your PC talk to your industrial hardware. Whether you're using a direct USB cable or a USB-XC programming cable , follow this guide to bridge the gap. 1. Identify Your Cable and Controller Xinje PLCs usually connect in one of two ways: Direct USB Port: Newer models (like the ) often have a built-in USB port. USB-to-Serial Cable: Many older or slim models (XC series) require a specialized USB-XC programming cable . This cable typically uses a or similar chip to convert USB to RS232. 2. Download the Driver Do not rely on Windows to find the driver automatically. Visit the official Xinje Download Center Look for the "USB driver" "USB-to-Serial" driver under the software or tools section.

If you are using a 3rd party programming cable, you may need the CH341 driver specifically. 3. Installation Steps Disconnect the PLC:

Unplug the USB cable from your PC before starting the installation to avoid "unidentified device" errors. Run the Installer: Right-click the driver installer ( ) and select "Run as Administrator." The "Success" Check:

Once the installation finishes, plug the cable back into your PC and the PLC. Device Manager Verification: Device Manager on your Windows PC. Expand the Ports (COM & LPT) You should see "USB-SERIAL CH341 (COMx)" "Xinje USB" without any yellow warning triangles. Note the COM Port Number (e.g., COM3). 4. Configure Your Software

After the driver is "live," you must point your programming software to the right gate: (for XC series) or XINJE Config Communication Settings Serial Port Settings Select the that matched the number you saw in Device Manager. "Test Communication" to confirm the link is active. Troubleshooting Tips Driver Signature Error:

If you are on Windows 10 or 11 and the driver won't install, you might need to temporarily disable driver signature enforcement in your Windows startup settings. Cable Sequence:

Always connect the cable to the PC first, wait for the chime, and then connect to the PLC. for your particular Xinje PLC model? Download Center - Wuxi Xinje Electric Co., Ltd.

To install the USB driver for a Xinje PLC, you typically need to install the Xinje PLC Programming Software (such as XDPPro or XS Studio), which includes the necessary driver files. 1. Identify Your PLC Series Xinje offers different software depending on the PLC model: XC Series: Uses XDPPro software.

XD/XL Series: Uses XDPPro (newer versions) or specific XD software. XS Series: Uses XS Studio (often based on CODESYS). 2. General Installation Steps

Download the Software: Visit the Xinje Download Center or regional sites like Xinje Malaysia to get the latest programming software for your specific series. Step 2: Install the Driver

Run the Installer: Execute the setup file as an administrator. The USB driver installation is usually bundled with the main software installation. Manual Driver Installation (if needed):

If the PLC is not recognized after software installation, connect the PLC to your PC via the USB cable. Open Device Manager on your Windows PC.

Look for an "Unknown Device" or a device labeled "Xinje PLC" under "Other devices" or "Ports (COM & LPT)". Right-click the device and select Update Driver.

Choose Browse my computer for drivers and point to the Driver or USB folder within the Xinje software installation directory (typically C:\Program Files (x86)\Xinje...). Verify Communication:

In the Xinje programming software, go to Communication Settings.

Select the correct connection type (USB or Serial via a USB-to-RS232 adapter like the USB-XC). Test the connection to ensure the PC can "see" the PLC. 3. Key Hardware Drivers

Xinje TH USB Device: Common for various Xinje interfaces; version 1.0.5.0 is a known stable version for certain legacy hardware.

USB-XC Cable: If you are using a conversion cable (USB-XC), it may require a separate Prolific or CH340 serial-to-USB driver if not automatically installed by Windows. 4. Safety and Connection Tips

Power Off: Always cut off external power before performing initial wiring or connecting expansion modules.

Cable Types: High-speed motion controllers (like the XDC series) or Ethernet-capable models (like the XD5) might use standard USB or Ethernet cables, but standard XC/XD models often require specific programming cables. XINJE PLC XD5 Series Programmable Controller User Manual

Installing a Xinje PLC USB driver is a straightforward process, but it requires specific steps to ensure your PC communicates correctly with the hardware. Follow this guide to get your connection up and running. 🛠️ Prerequisites Before starting, ensure you have the following: A Xinje PLC (XC, XD, or XL series) USB Programming Cable (usually a standard USB-A to USB-B or Mini-USB) XDPPro or XDPro Software installed on your Windows PC Administrator rights on your computer 📂 Step 1: Locate the Driver Files

Xinje drivers are typically bundled with their programming software. You don’t usually need to download a separate installer. Default Path: C:\Program Files (x86)\Xinje\XDPPro\USB_Driver If you are using the newer

software, look in the corresponding installation folder for the USB_Driver directory. 🔌 Step 2: Connect the Hardware Power on your into the PLC and then into your computer.

Windows will likely attempt to find a driver and fail, showing an "Unknown Device" in the Device Manager. ⚙️ Step 3: Manual Installation via Device Manager

Windows often fails to "auto-detect" these industrial drivers, so you must point it to the folder manually. Right-click the Start button and select Device Manager "Other Devices" "Ports (COM & LPT)" Right-click the device (often labeled "Xinje PLC" "USB Serial Port" ) and select Update Driver "Browse my computer for driver software" and navigate to the USB_Driver folder mentioned in Step 1.

. Windows will install the driver. You may see a security warning; select "Install this driver software anyway" ✅ Step 4: Verify the Connection Once installed, the device should appear under Ports (COM & LPT) as "USB Serial Port (COMx)" or under Universal Serial Bus controllers Communication Settings

as the connection type (or select the specific COM port assigned).

. If it says "Connection Successful," you are ready to upload or download code. 💡 Troubleshooting Tips Driver Signature Error:

If Windows 10/11 blocks the install, you may need to temporarily Disable Driver Signature Enforcement in the Advanced Startup settings. Cable Check:

If no device appears in Device Manager at all, try a different USB port or cable; industrial environments are tough on hardware. Software Version:

Ensure your software version matches your PLC series (XC series uses XDPPro; XD/XL series uses XDPro). If you'd like to dive deeper, I can help you with: Finding the latest download link for XDPPro/XDPro. Step-by-step instructions for Disabling Driver Signature Enforcement A guide on uploading your first program once the driver is fixed. Which of these would be most helpful for your project?

Method A: Using the Installer (Easiest)

  1. Navigate back to the Driver folder you found in Step 1.
  2. Double-click the install.exe or setup.exe file.
  3. Follow the on-screen prompts to complete the installation.
  4. Restart your computer if prompted.

Typical Installation Steps (What Works for Most)

  1. Install Xinje software first (e.g., XCPPro or AutoShop) – the driver files are usually in C:\Program Files (x86)\Xinje\Drivers\USB or similar.
  2. Connect PLC to PC via USB cable. PLC must be powered.
  3. Open Device Manager → find unknown device or “Xinje USB Device” with yellow exclamation.
  4. Right-click → Update driver → Browse my computer → point to that driver folder.
  5. If you see “driver not signed” error on Win10/11:
    • Restart PC → press F7 / Shift+Restart → Disable driver signature enforcement
    • Then repeat step 4.
  6. After success, the device appears under “Xinje USB Devices” (not COM & LPT).